| CONSOLIDATED BEARING 2307E-K 2RS Self Aligning Ball Bearings | C90 - Dynamic Radial Rating (90 million revolutions)5:3490 lbf; Cg - Geometry Factor:0.0606; Ab - Cage-Cone Frontface Clearance:0.07 in; Cage Type:Stamped Steel; R - Cone Backface To Clear Radius3:0.06 in; Cone Part Number:15102; C90(2) - Dynamic Radial Rating (Two-Row, 90 million revolutions)2:6080 lbf; G2 - Heat Generation Factor (Rib-Roller End):10; C0 - Static Radial Rating:12100 lbf; C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)1:23400 lbf; |
| CONSOLIDATED BEARING 2306 P/6 Self Aligning Ball Bearings | N:12mm; A4:20.5 mm; B:25 mm; A2:28 mm; Weight:0.66 kg; d:20 mm; S:7 mm; A1:6 mm; Dz:54 mm; T min.:-20 °C; |
| CONSOLIDATED BEARING 10406 C/3 Self Aligning Ball Bearings | A1:21.6 mm; Designation of housing:PP205-; L:108 mm; C:14 kN; J:86 mm; d:22.22 mm; N:11mm; Weight:0.28 kg; A:31.7 mm; H:28.6 mm; |
| SKF 2204 ETN9/W64F Self Aligning Ball Bearings | L1:65 mm; T max.:100 °C; H:57.2 mm; N1:25 mm; Dz:100 mm; A:60 mm; C:35.1 kN; B:43.5 mm; J:159 mm; C0:23.2 kN; |
| CONSOLIDATED BEARING 2303 C/3 Self Aligning Ball Bearings | L1:121.00 mm; C:23 mm; D3:165 mm; Locknut:KM26; Lockwasher and Lockplates:MB26; G:M130x2; Weight:4.55 Kg; d1:4 1/2 in; Appropriate Hydraulic Nut:HMV26; |
| SKF 1218/W64 Self Aligning Ball Bearings | Y1 - ISO Factor5:1.44; e - ISO Factor4:0.47; r - Cup Frontface To Clear Radius2:0.06 in; Series:94000; Y - ISO Factor1:1.28; Design Units:Imperial; C - Double Cup Width:5.5000 in; K - Factor3:1.25; Da - Cup Frontface Backing Diameter:11.02 in; Y2 - ISO Factor6:2.15; |
| SKF 11507 ETN9 Self Aligning Ball Bearings | B:25.4 mm; A2:49.4 mm; B1:38.9 mm; N:14mm; J:130 mm; Recommended tightening torque for set screw:11.5 Nm; T max.:100 °C; e:20 mm; T min.:-20 °C; C:25.7 kN; |
| CONSOLIDATED BEARING 2308 M Self Aligning Ball Bearings | C:113.36 kN; S:37.3 mm; d:74.61 mm; B1:100 mm; L:236 mm; Recommended tightening torque for set screw:54.5 Nm; Designation of housing:FS315-; G:M10x1; T max.:100 °C; C0:76.8 kN; |
| CONSOLIDATED BEARING 2308E-K 2RS C/3 Self Aligning Ball Bearings | K - Factor7:1.29; C - Cup Width:17.463 mm; G1 - Heat Generation Factor (Roller-Raceway):20.6; B - Cone Width:22.225 mm; Ca90 - Dynamic Thrust Rating (90 million revolutions)6:2980 lbf; D:80.963 mm; Design Units:Imperial; da - Cone Frontface Backing Diameter:39.62 mm; a - Effective Center Location3:-3.8 mm; Ab - Cage-Cone Frontface Clearance:3.1 mm; |
| SKF 2200E Self Aligning Ball Bearings | d1:32.4 mm; H1:76 mm; s1:30.5 mm; A1:12 mm; L3:51 mm; N:19mm; SW:3 mm; Weight:0.93 kg; L:94 mm; T max.:100 °C; |
| SKF 2208E Self Aligning Ball Bearings | C:14 kN; A:27 mm; A1:7 mm; T min.:-20 °C; A2:29.5 mm; L:115 mm; s1:13.5 mm; Recommended tightening torque for set screw:5.5 Nm; e:10 mm; C0:7.88 kN; |
| CONSOLIDATED BEARING 2307 Self Aligning Ball Bearings | d:20 mm; Category:Single Row Ball Bear; Weight / LBS:0.14991; Fatigue limit load, Cu:0.23 kN; Enclosure:2 Seals; Min operating temperature, Tmin:-25 °C; ra max:0.6 mm; Long Description:20MM Bore; 42MM Outs; rs min:0.6 mm; |
| CONSOLIDATED BEARING 1204 C/3 Self Aligning Ball Bearings | D:30 mm; C0 - Static Radial Rating:2680 N; da - Inner Ring Backing Diameter:20.0 mm; Design Units:METRIC; Ball Type:STEEL; R - Inner Ring To Clear Radius2:0.3 mm; Limiting Speed (Grease):45100 rpm; do - Ball Diameter:3.571875 mm; Limiting Speed (Oil):90200 rpm; Cage Type:CR - Phenolic Outer; |
| CONSOLIDATED BEARING 1202 Self Aligning Ball Bearings | G1 - Heat Generation Factor (Roller-Raceway):75.8; Db - Cup Backface Backing Diameter:129.03 mm; Cg - Geometry Factor:0.0873; Y - ISO Factor4:0.73; Da - Cup Frontface Backing Diameter:141.99 mm; Cup Part Number:Y31314M; C - Cup Width:25.000 mm; D:150 mm; G2 - Heat Generation Factor (Rib-Roller End):29.5; e - ISO Factor3:0.83; |
| SKF 1306E Self Aligning Ball Bearings | A:43 mm; Designation of bearing:EX211-34G2L3; B:55.4 mm; J:184 mm; Weight:3.28 kg; G:M6x1; s1:48.4 mm; T min.:-20 °C; T max.:100 °C; d1:74.5 mm; |
| CONSOLIDATED BEARING 11209 Self Aligning Ball Bearings | Recommended tightening torque for set screw:11.5 Nm; C:35.1 kN; N1:23 mm; Z:91.5 mm; d1:67.2 mm; s1:33.4 mm; L:200 mm; L1:61 mm; Designation of housing:PE210N-; T max.:100 °C; |